| 1609 | TIE (Blue; n4; Plastic; reusable) - Use for coiling the Cable Assembly among other things | EACH | $1.27 | |
| 2400 | NAIL PLUG (White; Plastic) - Use to plug small holes on the Body Assembly | EACH | $1.27 | |
| 3607 | WASHER (Use on All Pulley Assemblies; Use on Movable Axle of Jet / Rover cleaners; Rounded edges facing inward) | EACH | $5.83 | |
| 700014 | FLAT PLUG (Black; Plastic) - Use to plug medium holes on the Body Assembly of the Aquabot Ultra | EACH | $1.27 | |
| 7002 | FUSE (5.0 Amp; 250 Volt; Slow-Blow) - Aquabot Plus RC; Aquabot Ultra; All AMAX; All UMAX; All PHV | EACH | $3.07 | |
| 7109 | WASHER (St.Steel) - Use with n 2500 screw for Spacer Bracket or to fasten Back Plate Block to Body | EACH | $0.64 | |
| 800070 | NOVUS 2 Plastic Polish 24 oz. Bottle - Polish for the plastic components | EACH | $80.56 | |
| 8299 | ***SPACER BRACKET (w/ hardware) - Use when older Black Drive Motor Legs are too short for Pulley | ASSEMBLY | $23.32 | |
| 8351 | FLAT PLUG (White; Plastic) - Use to plug large holes on the Body Assembly | EACH | $1.27 | |
| A220203FCC | RECEIVER (Radio; 4-Way) - Aquabot Plus RC; Aquabot Ultra; Ultramax Junior; Ultramax - - - - - - FOR NEW Units only - Responds to 220114C and 220119C Transmitters - Older units need KIT | EACH | $233.14 | |
| A220203KIT | <p>
RECEIVER & TRANSMITTER KIT - Aquabot Plus RC; Aquabot Ultra; Ultramax Junior; Ultramax - - - - - - - - - KIT includes matched 220114C Radio RC Transmitter (Grey / Yellow face) and A220203FCC Receiver | SET OF 2 | $322.45 | |
| A800135 | <p>
MAIN DRAIN BUMPER - Can be used on most Pools' Main Drain; where a cleaner may get stuck</p>
<p>
<strong><span style="color: rgb(255, 0, 0);">This item Is replaced with Smart Ring!!</span></strong> | EACH | $79.20 | |
| SP1611 | SHRINK TUBE (3/4; Blue) - For sealing the Cable insulation below the P-Clip at the Handle Assembly | 4 FEET | $46.64 | |
| SP3007 | PVA CLIMBING RINGS (Light Blue PVA; 1" thick) - Fit over Rubber Brushes to add more traction ** | SET OF 4 | $26.71 | |
| SP3107 | MOTOR FLOAT (8 Shape) ** only when specified by Aqua Products | SET OF 3 | $9.43 | |
| SP3502 | TENSION DEVICE (OLD; replaced by Stepped Sleeve Rollers) - Formerly used to add Tension to Drive Belts | EACH | $37.10 | |
| 1 | A10201 | <p>
HANDLE ASSY. (Blue & White; Bracket included) - Aquabot Ultra; Aquamax | EACH | $115.96 | |
| 1 | A10203L | <p>
HANDLE ASSY. (Blue & White with Light; Bracket not included) - Aquabot Ultra Lumina | EACH | $291.48 | |
| 2 | S1100B | HANDLE BRACKET (Blue) - All Aquabot except T series; All Aquamax; All Ultramax cleaners listed | EACH | $34.85 | |
| 4 | 11003 | CLEVIS PIN (Round Head; hole in end) - Use to link the Handle Assembly arm to the Handle Bracket | EACH | $2.86 | |
| 6 | 11004 | WASHER (St.Steel) - Use around the Clevis Pin underneath the Cotter Ring on Handle Assembly Bracket | EACH | $0.83 | |
| 7 | 11005 | COTTER RING (Aluminum; 3/16") - Use at end of the Clevis Pin to hold the Handle Bracket | EACH | $0.83 | |
| 8 | 1105 | SCREW (10-32; 7/8; Phil Pan Head) - Use to fasten the Handle Bracket to the Body Assembly | EACH | $1.27 | |
| 10 | 2500 | SCREW (#8; 1-1/4 Pan Head) - Used to fasten the Back Plate Block to the Body Assembly | EACH | $1.27 | |
| 12 | 2103 | P-CLIP (11/16; Plastic) - Use to fasten the foam-insulated part of a 9-wire cable to the Handle Assy. | EACH | $1.27 | |
| 12 | 2111 | P-CLIP (5/8"; Coated Steel) - Use to fasten the insulated part of a 4;7;9-wire cable to the Handle Assy. | EACH | $2.44 | |
| 12 | 2112 | P-CLIP (11/16; St.Steel) - Use to fasten the foam-insulated part of a 9-wire cable to the Handle Assy. | EACH | $2.44 | |
| 13 | 2700 | SCREWS (8; 11/16; Phil Pan-Flat Head) - Use to fasten P-Clips; and Drive Motors | EACH | $1.27 | |
| 14 | 2260 | SCREWS (6; 7/16; Phil Pan-Flat Head) - Use for P-Clips; Outlet Top; and H-Float | EACH | $1.27 | |
| 15 | 1640E | PLUG (7-Pin; Male) - Aquabot Plus RC; Aquabot Ultra; Aquabot Turbo T4 (version 2006) | EACH | $45.79 | |
| 16 | S7935 | EZ-SWIVEL (For 4;5;7;or 9-wire Cable) - Can be used on any Cable Assembly with 4 or more wires | ASSEMBLY | $46.62 | |
| 17 | A16120 | CABLE ASSY. (7-Wire; 75 Foot; Floating) - Aquabot Plus RC; Aquabot Ultra | EACH | $456.53 | |
| 25 | 2230B | OUTLET TOP (Top and Bottom) - Aquabot / Storm / Turbo / Tempo / Plus RC / Ultra; Aquamax / Jr / Biturbo | EACH | $30.32 | |
| 26 | A22201UB | BODY ASSY. (White; with Lock Tabs; Outlet Ring; Inserts) - Aquabot Ultra | EACH | $215.60 | |
| 27 | 2251 | SCREW (8-18 x 3/4; Phil Small Head) - Use for Pump to Body in some cleaners; and Jet Valve Assembly | EACH | $1.27 | |
| 29 | SP2300 | ANTI-ROLL BRACKETS (Plastic; White) - Aquabot / Turbo / Plus RC / Ultra; Aquamax / Jr / Biturbo | SET OF 4 | $11.77 | |
| 30 | SP3402 | LOCK-NUTS (Hex; Nylon insert; for various uses: Sideplate Bolts; Anti-Roll Brackets; Pole Handle Assy.) | SET OF 8 | $6.72 | |
| 31 | 2261 | SCREW (M-5; Phil Bev Head) - Use to fasten the Anti-Roll Brackets to the Body Assembly | EACH | $1.27 | |
| 36 | SP9204BL | LOCK-TABS (Blue; Plastic) - For All Body Assemblies; used to hold Bottom Lids to base of cleaners | SET OF 2 | $3.60 | |
| 38 | 2303 | SCREWS (18-8; 8/32 x 1/2; Phil Bev Head) - Use to fasten the Lock-Tabs to the Body Assembly | EACH | $1.27 | |
| 39 | 7133 | LOCK-NUT (Nylon Insert; Hex) - Use to fasten the Screws of the Lock-Tabs | EACH | $0.83 | |
| 45 | S3400B | SIDEPLATE (Blue; 4 holes for Bolts; 2 holes to Motor) - Aquabot Plus RC / Ultra; Aquamax / Biturbo; Ultramax / Jr | EACH | $30.32 | |
| 49 | SP3401 | SCREW (Bolts; Long; For Sideplate) - Aquabot Plus RC / T4 / Ultra; All Aquamax & Ultramax units | SET OF 8 | $9.54 | |
| 51 | 2600 | BUSHING (White; Plastic) - All Aquabot cleaners; All listed Aquamax and Ultramax cleaners | EACH | $2.76 | |
| 54 | 3500 | SMALL ROLLER (White; Plastic) - Supports the Drive Track; install on lower legs of Sideplate | EACH | $2.76 | |
| 56 | 3506 | STEPPED SLEEVE ROLLER (White; Thicker end supports Drive Belts; Install on upper Sideplate legs) | EACH | $2.76 | |
| 57 | SP3302 | DRIVE BELTS (Tan) | PAIR | $17.38 | |
| 58 | A3605 | PULLEY ASSEMBLY (Medium; ~ 2.75 inches) - Use for cleaners with Black Drive Motors | EACH | $33.81 | |
| 58 | A3608 | PULLEY ASSEMBLY (Long; OLD; ~ 3.5 inches) *** See Drive Motor Spacer Bracket n 8299 | EACH | $33.81 | |
| 60 | A6010U | PUMP MOTOR (Aquabot Plus RC; AB Ultra; Aquamax Jr Plus; Aquamax; AMAX Biturbo; Ultramax Jr; UMAX) | EACH | $282.74 | |
| 61 | 4400 | PROPELLER - Most cleaners | EACH | $12.25 | |
| 79 | A2243S | JUNCTION BOX ASSY. (Connections: 7-Pin; 1 Pump Motor; 2 Drive Motor) - Aquabot Plus RC / Ultra | EACH | $209.88 | |
| 79 | A2243SL | JUNCTION BOX ASSY. (Connections: 7-Pin; 1 Pump Motor; 1 Light; 2 Drive Motor) - Aquabot Ultra Lumina | EACH | $227.37 | |
| 79 | A2244S | JUNCTION BOX ASSY. (Connections: 7-Pin; 1 Pump Motor; 2 IR; 2 Drive Motor) - Aquabot Ultra Infra Red | EACH | $227.37 | |
| 80 | A8526SL | DRIVE MOTOR (MASTER; Black) - Aquabot Plus RC; Aquabot Ultra | EACH | $582.91 | |
| 80 | A8532V | DRIVE MOTOR (SLAVE; Green) - Use for all units which use two Drive Motors | EACH | $519.66 | |
| 83 | 4613 | SPIRAL PIN (3/4"; solid Stainless Steel) - Used in the end of the Drive Motor shaft; use Lock-Tite | EACH | $1.27 | |
| 86 | SP5474 | SHRINKABLE BUTT CONNECTORS (Light Blue; crimp closed and heat shrink to seal) | PAIR | $2.54 | |
| 87 | SP1617 | SHRINK TUBE (5/16; Blue) - For sealing 2-wire connections; use under Heat Shrink 1619 | 4 FEET | $46.64 | |
| 87 | SP1619 | SHRINK TUBE (1/2; Black) - For sealing 2-wire connections; use over Heat Shrink 1617 | 4 FEET | $46.64 | |
| 88 | 1625 | SHRINK TUBE (3/4; Black) - For sealing all medium sized connections at the Junction Box | 4 FEET | $46.64 | |
| 89 | SP1614 | SHRINK TUBE (1-1/2; Black) - For sealing wide connections at the Junction Box and Cable Assembly | 4 FEET | $46.64 | |
| 89 | SP1614S | SHRINK TUBE (1-1/2; 2.5; Black) - Service kit for sealing large Cable connections | EACH | $2.44 | |
| 90 | A38201MG | WHEEL TUBE ASSY (NEW; Aquabot Ultra; Ultramax Junior) - Model 'G' | EACH | $108.44 | |
| 91 | 11058 | RETAINING RING (E-Clip; New Style) - Aquabot Turbo; AB Plus RC; Aquabot T4; AB Ultra; All AMAX / UMAX | EACH | $3.67 | |
| 92 | 3603 | WASHER (Nylon; Flat) - Use for All cleaners on the end of Wheel or Wheetube Assembly | EACH | $1.27 | |
| 96 | 1109 | SCREW (Small; to fasten Wheeltube Brace to Body) - Aquabot Plus RC / Ultra; Ultramax Junior | EACH | $1.27 | |
| 97 | SP3002BM4 | RUBBER BRUSHES (Blue Molded Rubber; cut in half; Long) - Aquabot Ultra; Ultramax Junior | SET OF 4 | $83.42 | |
| 97 | SP3008A | PVA CLIMBING BRUSHES (Light Blue PVA Foam; cut in half; Long) - Aquabot Ultra; Ultramax Junior | SET OF 4 | $131.84 | |
| 99 | 3200 | <p>
DRIVE TRACK (Black) | EACH | $22.24 | |
| 99 | 3201 | <p>
DRIVE TRACK (Blue) | EACH | $22.20 | |
| 99 | 3203 | DRIVE TRACK with TRACTION TABS (Blue) - For all Model 'G' units | EACH | $22.24 | |
| 100 | SP2675 | MODEL G SPACER BRACKETS ** necessary with 'Model G' Drive Tracks | SET OF 4 | $4.88 | |
| 101 | 8101 | FILTER BAG (Fine) - Aquabot Ultra; Aquamax / Biturbo; Ultramax Junior; JetMax; Power Handi-Vac 200 | EACH | $72.36 | |
| 101 | 8201 | FILTER BAG (Mesh) - Aquabot Ultra; Aquamax / Biturbo; Ultramax Junior; JetMax; Power Handi-Vac 200 | EACH | $70.15 | |
| 102 | SP8001 | FILTER BAG CLIP (Black; Plastic) - Aquabot Ultra; Aquamax / Biturbo; Ultramax Jr; JetMax; PHV 200 | PAIR | $8.10 | |
| 103 | 5301 | FILTER SCREEN (White; Cage) - Aquabot Ultra; Aquamax / Biturbo; Power Handi-Vac 200; Ultramax Junior | EACH | $34.05 | |
| 104 | 2702 | SCREW (6; 11/16; Phil Pan-Flat Head; Pointed) - For fastening the 5300 / 5301 Filter Screen to the Body | EACH | $1.27 | |
| 105 | A9201XC | BOTTOM LID ASSY. (White; Square Wire Frame) - Aquabot Ultra; JetMax; Aquamax / Biturbo; PHV 200 | EACH | $115.43 | |
| 107 | 9301 | INTAKE VALVE FLAP (Black PVC Rubber) - Aquabot Ultra; Aquamax / Biturbo; JetMax; PHV 200 | EACH | $2.44 | |
| 108 | S3103 | H-FLOAT (Foam; Plastic; with Screws) - Fasten to Bottom Lid if cleaner's wall-climbing is not high enough | ASSEMBLY | $11.64 | |
| 109 | SP3104 | SIDE POCKET FLOATS (White; Foam Blocks) - Put in Bottom Lid if wall-climbing is not high enough | PAIR | $3.71 | |
| 110 | A7072 |
POWER SUPPLY (7-Pin; Female Socket; Radio RC) - Aquabot Plus RC; Aquabot Ultra | EACH | $426.00 | |
| 111 | 7136 | SOCKET ASSY. (7-Pin; Male; 7-Wire) - Aquabot T4; All Aquamax RC cleaners; Old Aquabot Plus RC / Ultra | EACH | $34.05 | |
| 111 | 7149E | SOCKET ASSY. (7-Pin; Female; 7-Wire) - Aquabot Plus RC; Aquabot Ultra | EACH | $34.05 | |
| 112 | 7005 | <p>
FUSE HOLDER (Standard; Push & Turn style) - Most Residential and Commercial cleaners | EACH | $8.14 | |
| 112 | 7205 | FUSE HOLDER (Alternate; Phillips Head style) - Only when specified by Aqua Products Service | EACH | $8.14 | |
| 114 | 7106 | WIDE SWITCH (Wide; 1¼ x ¾; Red; 3-Wire) - Use for Power Supply | EACH | $8.16 | |
| 115 | 7023 | ANTENNA (4; with Hardware) - Aquabot T4; Aquabot Plus RC; Aquabot Ultra; UMAX Jr; Ultramax; Gemini | EACH | $11.66 | |
| 116 | 220119C | TRANSMITTER (Radio RC; Grey & Yellow/ Blue???/ Red LED light) - Aquabot Plus RC; Aquabot Ultra -- -- -- -- -- -- -- FOR NEW Units only - Transmits to A220203FCC Receiver - Older units will need KIT | EACH | $89.32 | |
| 117 | 7041A | HANDLE (Plastic; with Hardware) - Use on All Power Supplies except Ultramax Jr; Ultramax; and PHV 300 | ASSEMBLY | $6.23 | |
| 118 | 7102 | CORD FOR POWER SUPPLY (3-Wire; Green; Black; and White) - Use on All Power Supplies | EACH | $11.66 | |
| 119 | 7272 | OUTDOOR TIMER (8hr; Programmable; GFCI) - Use to regulate cleaner's run time when no Auto shut-off | EACH | $46.58 | |
Information
Categories
Shopping Cart
Specials