| 1609 | TIE (Blue; n4; Plastic; reusable) - Use for coiling the Cable Assembly among other things | EACH | $1.27 | |
| 2008 | SCREWS (Use to hold IR Brace inside of Outer Shell) - Screw from outside of Shell into IR Brace Assembly | EACH | $1.27 | |
| 2009 | IR BRACE ASSEMBLY (all hardware included) - Use to hold the IR Sensor in position on the cleaner | ASSEMBLY | $23.32 | |
| 2209 | INFRA RED SENSOR (Aquamax Jr Plus; Aquamax; Aquamax Biturbo) | EACH | $162.69 | |
| 2400 | NAIL PLUG (White; Plastic) - Use to plug small holes on the Body Assembly | EACH | $1.27 | |
| 3607 | WASHER (Use on All Pulley Assemblies; Use on Movable Axle of Jet / Rover cleaners; Rounded edges facing inward) | EACH | $5.83 | |
| 7002 | FUSE (5.0 Amp; 250 Volt; Slow-Blow) - Aquabot Plus RC; Aquabot Ultra; All AMAX; All UMAX; All PHV | EACH | $3.07 | |
| 7109 | WASHER (St.Steel) - Use with n 2500 screw for Spacer Bracket or to fasten Back Plate Block to Body | EACH | $0.64 | |
| 800001 | PUTTY (Grey; Waterproof) - For waterproofing the Terminal Basin in all White Drive Motors | 1 Lb | $9.94 | |
| 800070 | NOVUS 2 Plastic Polish 24 oz. Bottle - Polish for the plastic components | EACH | $80.56 | |
| 8351 | FLAT PLUG (White; Plastic) - Use to plug large holes on the Body Assembly | EACH | $1.27 | |
| A1620 | CABLE ASSY. (For TANK DEMO; 2-Wire; 10 Foot; Floating) - Aquabot / Turbo; Aquamax Junior HT / Plus | EACH | $43.44 | |
| A220200FCC | RECEIVER (Radio; 2-Way) - Aquabot Turbo RC; Aquamax RC; Aquamax Biturbo RC - - - - - - - - FOR NEW Units only - Responds to 220117C Transmitter - Older units will need to order KIT | EACH | $233.14 | |
| A220200KIT | <p>
RECEIVER & TRANSMITTER KIT - Aquabot Turbo RC; Aquamax RC; Aquamax Biturbo RC - - - - - - - - - KIT includes matched 220117C Radio RC Transmitter (Grey / Yellow face) and A220200FCC Receiver | SET OF 2 | $301.04 | |
| A800135 | <p>
MAIN DRAIN BUMPER - Can be used on most Pools' Main Drain; where a cleaner may get stuck</p>
<p>
<strong><span style="color: rgb(255, 0, 0);">This item Is replaced with Smart Ring!!</span></strong> | EACH | $79.20 | |
| SP1611 | SHRINK TUBE (3/4; Blue) - For sealing the Cable insulation below the P-Clip at the Handle Assembly | 4 FEET | $46.64 | |
| SP3007 | PVA CLIMBING RINGS (Light Blue PVA; 1" thick) - Fit over Rubber Brushes to add more traction ** | SET OF 4 | $26.71 | |
| SP3502 | TENSION DEVICE (OLD; replaced by Stepped Sleeve Rollers) - Formerly used to add Tension to Drive Belts | EACH | $37.10 | |
| SP5173 | WEIGHTS (Black) - Put in Bottom Lid if cleaner's wall-climbing is too high; or to help JetMax / Jr sink to floor | PAIR | $6.97 | |
| 1 | A10000B | <p>
HANDLE ASSY. (Blue & White; Bracket included) - Aquabot / Storm / Turbo / Tempo / Plus RC; Aquamax Jr | EACH | $103.88 | |
| 2 | S1100B | HANDLE BRACKET (Blue) - All Aquabot except T series; All Aquamax; All Ultramax cleaners listed | EACH | $34.85 | |
| 4 | 11003 | CLEVIS PIN (Round Head; hole in end) - Use to link the Handle Assembly arm to the Handle Bracket | EACH | $2.86 | |
| 6 | 11004 | WASHER (St.Steel) - Use around the Clevis Pin underneath the Cotter Ring on Handle Assembly Bracket | EACH | $0.83 | |
| 7 | 11005 | COTTER RING (Aluminum; 3/16") - Use at end of the Clevis Pin to hold the Handle Bracket | EACH | $0.83 | |
| 8 | 1105 | SCREW (10-32; 7/8; Phil Pan Head) - Use to fasten the Handle Bracket to the Body Assembly | EACH | $1.27 | |
| 10 | 2500 | SCREW (#8; 1-1/4 Pan Head) - Used to fasten the Back Plate Block to the Body Assembly | EACH | $1.27 | |
| 12 | 2100 | P-CLIP (1/4; Plastic) - Use to fasten the non-foam-insulated part of a 2-wire cable to the Body | EACH | $1.27 | |
| 12 | 2102 | P-CLIP (7/16; Plastic) - Use to fasten the foam-insulated part of a 2-wire cable to the Handle Assy. | EACH | $1.27 | |
| 12 | 2104 | P-CLIP (3/8"; Plastic) - Use to fasten the foam-insulated part of a 2-wire cable to the Body | EACH | $1.27 | |
| 12 | 2111 | P-CLIP (5/8"; Coated Steel) - Use to fasten the insulated part of a 4;7;9-wire cable to the Handle Assy. | EACH | $2.44 | |
| 12 | 8316 | P-CLIP (9/16; Plastic) - Use to fasten the Heat Shrink part of the 2-wire cable to the Handle Assy. | EACH | $1.27 | |
| 13 | 2700 | SCREWS (8; 11/16; Phil Pan-Flat Head) - Use to fasten P-Clips; and Drive Motors | EACH | $1.27 | |
| 14 | 2260 | SCREWS (6; 7/16; Phil Pan-Flat Head) - Use for P-Clips; Outlet Top; and H-Float | EACH | $1.27 | |
| 15 | 1601 | PLUG (3-Pin; Female; 2-Wire) - Aquabot / Storm / Turbo / Tempo / T2; Aquamax; Aquamax Jr; All Jet / Rover | EACH | $14.63 | |
| 15 | 1635 | PLUG (4-Pin; Female; 4-Wire) - Aquabot Turbo Solo / Turbo RC; Aquamax Jr RC; Aquamax Biturbo | EACH | $45.79 | |
| 16 | S7930 | EZ-SWIVEL (For 2-wire Cable) - Can be used on any 2-wire Cable Assembly | ASSEMBLY | $46.62 | |
| 16 | S7935 | EZ-SWIVEL (For 4;5;7;or 9-wire Cable) - Can be used on any Cable Assembly with 4 or more wires | ASSEMBLY | $46.62 | |
| 17 | 1675FM | CABLE ASSY. (2-Wire; 75 Foot; Floating) - Aquabot Plus; Aquamax Junior HT; JetMax Junior | EACH | $353.03 | |
| 17 | A16101 | CABLE ASSY. (2-Wire; 100 Foot; Floating Cable; 0.5" Diameter) - JetMax; Aquamax Junior Plus | EACH | $507.84 | |
| 17 | A16119 | CABLE ASSY. (7-Wire; 120 Foot; Floating) - Aquamax Junior Plus RC; Aquamax Biturbo RC | EACH | $737.13 | |
| 25 | 2230B | OUTLET TOP (Top and Bottom) - Aquabot / Storm / Turbo / Tempo / Plus RC / Ultra; Aquamax / Jr / Biturbo | EACH | $30.32 | |
| 26 | A22000 | BODY ASSY. (White; with Lock Tabs; Pin; Outlet Ring; Inserts) - Aquabot / Turbo; Aquamax Junior | EACH | $138.65 | |
| 26 | A22000 | BODY ASSY. (White; w/ Lock Tabs; Pin; Outlet Ring; Inserts) - Aquabot Turbo Solo / RC; Aquamax Jr Solo / RC | EACH | $138.65 | |
| 27 | 2251 | SCREW (8-18 x 3/4; Phil Small Head) - Use for Pump to Body in some cleaners; and Jet Valve Assembly | EACH | $1.27 | |
| 29 | SP2300 | ANTI-ROLL BRACKETS (Plastic; White) - Aquabot / Turbo / Plus RC / Ultra; Aquamax / Jr / Biturbo | SET OF 4 | $11.77 | |
| 30 | SP3402 | LOCK-NUTS (Hex; Nylon insert; for various uses: Sideplate Bolts; Anti-Roll Brackets; Pole Handle Assy.) | SET OF 8 | $6.72 | |
| 31 | 2261 | SCREW (M-5; Phil Bev Head) - Use to fasten the Anti-Roll Brackets to the Body Assembly | EACH | $1.27 | |
| 36 | SP9204BL | LOCK-TABS (Blue; Plastic) - For All Body Assemblies; used to hold Bottom Lids to base of cleaners | SET OF 2 | $3.60 | |
| 38 | 2303 | SCREWS (18-8; 8/32 x 1/2; Phil Bev Head) - Use to fasten the Lock-Tabs to the Body Assembly | EACH | $1.27 | |
| 39 | 7133 | LOCK-NUT (Nylon Insert; Hex) - Use to fasten the Screws of the Lock-Tabs | EACH | $0.83 | |
| 45 | S3400B | SIDEPLATE (Blue; 4 holes for Bolts) - Aquamax Junior HT; Aquamax Junior Plus | EACH | $30.32 | |
| 49 | SP3401 | SCREW (Bolts; Long; For Sideplate) - Aquabot Plus RC / T4 / Ultra; All Aquamax & Ultramax units | SET OF 8 | $9.54 | |
| 51 | 2600 | BUSHING (White; Plastic) - All Aquabot cleaners; All listed Aquamax and Ultramax cleaners | EACH | $2.76 | |
| 52 | 2610 | BUSHING (White; Plastic; Use for Pin on Body Assembly) - Aquabot / Storm / Turbo / Tempo; All Aquamax | EACH | $4.66 | |
| 54 | 3500 | SMALL ROLLER (White; Plastic) - Supports the Drive Track; install on lower legs of Sideplate | EACH | $2.76 | |
| 55 | 3700 | LARGE ROLLER (White; Plastic) - Supports the Drive Track; installs on Body Assembly Pin Support | EACH | $3.60 | |
| 56 | 3506 | STEPPED SLEEVE ROLLER (White; Thicker end supports Drive Belts; Install on upper Sideplate legs) | EACH | $2.76 | |
| 57 | SP3302 | DRIVE BELTS (Tan) | PAIR | $17.38 | |
| 58 | A3600 | PULLEY ASSEMBLY (Short; ~ 2.5 inches) - Use for cleaners with White Drive Motors | EACH | $27.98 | |
| 58 | A3605 | PULLEY ASSEMBLY (Medium; ~ 2.75 inches) - Use for cleaners with Black Drive Motors | EACH | $33.81 | |
| 60 | A6001T | PUMP MOTOR (Aquabot Turbo; Aquabot Tempo; Aquamax Jr HT) | EACH | $213.79 | |
| 60 | A6010U | PUMP MOTOR (Aquabot Plus RC; AB Ultra; Aquamax Jr Plus; Aquamax; AMAX Biturbo; Ultramax Jr; UMAX) | EACH | $282.74 | |
| 61 | 4400 | PROPELLER - Most cleaners | EACH | $12.25 | |
| 65 | A2207 | DC PUMP FILTER (White; Plastic) - Aquabot Turbo Solo / Turbo RC; All Aquamax RC / Solo cleaners | ASSEMBLY | $52.47 | |
| 66 | 300099 | TUBING (Clear PVC; 5/16ID x 7/16OD) - Use to divert water from the DC Pump Filter to the DC Pump | PER FOOT | $1.10 | |
| 67 | 700038 | SPACER BLOCK (Grey; Stepped shape) - Use to position the Piston apart from the Model G Drive Tracks | EACH | $10.58 | |
| 68 | S300092 | DC PUMP MOTOR (Single; no Gate; 2-Wire) - Aquabot Turbo Solo; All Aquamax Solo / IR cleaners | EACH | $74.62 | |
| 68 | S300093 | DC PUMP MOTOR (Dual; with Gate; 2-Wire) - Aquabot Turbo RC; Aquabot T4; All Aquamax RC cleaners | EACH | $74.62 | |
| 69 | 300111 | TUBING (Clear PVC; 3/16ID x 5/16OD) - Use to divert water from the DC Pump to the Piston Assembly | PER FOOT | $1.10 | |
| 70 | 300108 | CLAMP BRACKET (Grey; Plastic; Wide) - Aquabot Turbo Solo / RC; All Aquamax RC / Solo cleaners | EACH | $2.27 | |
| 70 | 300109 | CLAMP (Grey; Plastic; Narrow) - Aquabot Turbo Solo / RC / T4; All Aquamax RC / Solo cleaners | EACH | $2.27 | |
| 71 | 300107 | BACK PLATE BLOCK (Grey; 4 holes) - Use to support the DC Pump Motor inside of the Body Assembly | EACH | $2.27 | |
| 72 | SP6204 | SPACER (Plastic; cylinder) - Use to make space between the Back Plate Block and the Body Assembly | SET OF 4 | $3.32 | |
| 73 | 1107 | SCREW (10-32; 1-3/4 Phil Pan Head) - Use to fasten Clamp & Piston onto Sideplate of a Model G cleaner | EACH | $1.27 | |
| 74 | 2301 | SCREW (10-32; 1/2 Phil Pan Head) - Use with Clamp to fasten Piston to Sideplate and DC Pump to Block | EACH | $1.27 | |
| 77 | S300090 | PISTON ASSEMBLY (White; Plastic) - One Piston is used for Solo cleaners; Two are used for RC cleaners | EACH | $68.67 | |
| 78 | 300084 | RUBBER TIP (White; Rubber) - Use at the bottom of the plunger of the Piston Assembly | EACH | $2.27 | |
| 80 | A4510D | DRIVE MOTOR (For TNK DEMO unit; White; Terminal Basin) - Aquabot / Aquabot Turbo Tank Demo | EACH | $289.11 | |
| 80 | A4510T | DRIVE MOTOR (White; Terminal Basin) - Aquabot Turbo; Turbo Solo; Aquabot Tempo; Aquamax Jr HT | EACH | $303.00 | |
| 80 | A4518 | DRIVE MOTOR (White; Terminal Basin) - Aquamax Junior Plus | EACH | $349.14 | |
| 80 | A8511IR | DRIVE MOTOR (Black; bare wire leads) - Aquamax Jr Plus IR; Aquamax IR; Aquamax Biturbo IR | EACH | $422.21 | |
| 80 | A8516MBTS | DRIVE MOTOR (Black; bare wire leads) - Aquamax Junior Plus Solo; Aquamax Solo; Aquamax Biturbo Solo | EACH | $422.21 | |
| 80 | A8517MBT | DRIVE MOTOR (Black; 2 bare wire leads) - Aquamax / Biturbo; Aquamax RC; Aquamax Jr Plus RC; Biturbo RC | EACH | $422.21 | |
| 81 | SP4619 | LOOP CONNECTOR (Metal; Crimp on wire) - Use to attach wires to Brass Terminals on White Drive Motor | PAIR | $1.27 | |
| 82 | 4618 | BRASS NUTS (Hex; small) - Use for attaching the Loop Connectors of wires to Brass Terminals | EACH | $1.27 | |
| 83 | 4613 | SPIRAL PIN (3/4"; solid Stainless Steel) - Used in the end of the Drive Motor shaft; use Lock-Tite | EACH | $1.27 | |
| 84 | 5000 | TERMINAL COVER (Plastic; Rectangle) - For covering the Basin in all White Drive Motors | EACH | $2.44 | |
| 85 | 4501 | SCREW (8-18 x 1/2; Phil Pan Head) - Use to fasten the Terminal Cover and the Extension Brackets | EACH | $1.27 | |
| 86 | SP5474 | SHRINKABLE BUTT CONNECTORS (Light Blue; crimp closed and heat shrink to seal) | PAIR | $2.54 | |
| 87 | SP1617 | SHRINK TUBE (5/16; Blue) - For sealing 2-wire connections; use under Heat Shrink 1619 | 4 FEET | $46.64 | |
| 87 | SP1619 | SHRINK TUBE (1/2; Black) - For sealing 2-wire connections; use over Heat Shrink 1617 | 4 FEET | $46.64 | |
| 90 | A38205 | WHEEL TUBE ASSY (OLD; Aquabot Turbo; Aquamax Junior HT; Aquamax Junior Plus) | EACH | $69.94 | |
| 90 | A38205MG | WHEEL TUBE ASSY (NEW; Aquabot Turbo; Aquamax Junior HT; Aquamax Junior Plus) - Model 'G' | EACH | $69.94 | |
| 91 | 11058 | RETAINING RING (E-Clip; New Style) - Aquabot Turbo; AB Plus RC; Aquabot T4; AB Ultra; All AMAX / UMAX | EACH | $3.67 | |
| 92 | 3603 | WASHER (Nylon; Flat) - Use for All cleaners on the end of Wheel or Wheetube Assembly | EACH | $1.27 | |
| 97 | SP3002B | RUBBER BRUSHES (Blue Molded Rubber; Short) - Aquabot / Turbo; Aquamax Jr HT / Jr Plus; Ultramax *** | PAIR | $77.89 | |
| 97 | SP3003B | RUBBER BRUSHES (Black Molded Rubber; Short) - Aquabot / Turbo / T4 (2004-2005); Aquamax Jr; Ultramax *** | PAIR | $77.89 | |
| 97 | SP3009 | PVA CLIMBING BRUSHES (Light Blue PVA Foam; Short) - Aquabot / Turbo; Aquamax Jr units; Ultramax *** | PAIR | $64.00 | |
| 97 | SPA2900 | SPONGE BRUSHES (Black Sponge Foam; Short) - Aquabot; Turbo; Aquamax Junior HT; Aquamax Jr Plus | PAIR | $66.76 | |
| 99 | 3200 | <p>
DRIVE TRACK (Black) | EACH | $22.24 | |
| 99 | 3201 | <p>
DRIVE TRACK (Blue) | EACH | $22.20 | |
| 99 | 3203 | DRIVE TRACK with TRACTION TABS (Blue) - For all Model 'G' units | EACH | $22.24 | |
| 100 | SP2675 | MODEL G SPACER BRACKETS ** necessary with 'Model G' Drive Tracks | SET OF 4 | $4.88 | |
| 101 | 8100 |
<p> FILTER BAG (Fine) - Aquabot / Turbo / Plus RC / T2 / T4 (2006); Aquamax Jr; PHV 100/300; small Jet / Rover; UMAX ** | EACH | $48.97 | |
| 101 | 8200 | <p>
FILTER BAG (Mesh) - Aquabot / Turbo / Plus RC; Aquamax Jr; PHV 100/300; small Jet & Rover; UMAX ** | EACH | $49.00 | |
| 103 | 5300 | FILTER SCREEN (White; Cage) - Aquabot / Turbo / Plus RC; AMAX Jr; PHV 100/300; small Jet / Rover; UMAX ** | EACH | $27.88 | |
| 104 | 2702 | SCREW (6; 11/16; Phil Pan-Flat Head; Pointed) - For fastening the 5300 / 5301 Filter Screen to the Body | EACH | $1.27 | |
| 105 | A9200X | BOTTOM LID ASSY. (White; W-shaped Wire Frame) - Aquabot; small Jet / Rover; Aquamax Jr; Ultramax *** | EACH | $92.11 | |
| 106 | 9305BL | INTAKE VALVE FLAP (Blue Plastic) - Fits into Intake of All small n 9200 Bottom Lids | EACH | $4.60 | |
| 108 | S3103 | H-FLOAT (Foam; Plastic; with Screws) - Fasten to Bottom Lid if cleaner's wall-climbing is not high enough | ASSEMBLY | $11.64 | |
| 109 | SP3104 | SIDE POCKET FLOATS (White; Foam Blocks) - Put in Bottom Lid if wall-climbing is not high enough | PAIR | $3.71 | |
| 110 | 7063C |
POWER SUPPLY (3-Prong; Male Socket) - Aquamax Jr HT; Aquamax Jr Plus; Aquamax; PHV 100 | EACH | $279.00 | |
| 110 | A7082 |
POWER SUPPLY (4-Prong; Male Socket) - Aquamax Junior Plus RC; Aquamax RC | EACH | $426.00 | |
| 111 | 7108 | SOCKET ASSY. (3-Pin; Male; 2-Wire) - Aquabot / Turbo / T2; All Jet and Rover cleaners; Aquamax / Jr | EACH | $10.49 | |
| 111 | 7135 | SOCKET ASSY. (4-Pin; Male; 4-Wire) - Aquabot Turbo Solo / Turbo RC; Aquamax Biturbo | EACH | $34.05 | |
| 112 | 7005 | <p>
FUSE HOLDER (Standard; Push & Turn style) - Most Residential and Commercial cleaners | EACH | $8.14 | |
| 112 | 7205 | FUSE HOLDER (Alternate; Phillips Head style) - Only when specified by Aqua Products Service | EACH | $8.14 | |
| 114 | 7106 | WIDE SWITCH (Wide; 1¼ x ¾; Red; 3-Wire) - Use for Power Supply | EACH | $8.16 | |
| 115 | 7024 | ANTENNA (4; with Hardware) - Aquamax Jr Plus RC; Aquamax RC; Aquamax Biturbo RC | EACH | $11.66 | |
| 116 | 220117C | TRANSMITTER (Radio RC; Grey & Yellow/ Blue??/ Red LED light) - Aquabot Turbo RC; Aquamax RC's -- -- -- -- -- -- -- -- FOR NEW Units only - Transmits to A220200FCC Receiver - Older units will need KIT | EACH | $69.90 | |
| 117 | 7041A | HANDLE (Plastic; with Hardware) - Use on All Power Supplies except Ultramax Jr; Ultramax; and PHV 300 | ASSEMBLY | $6.23 | |
| 118 | 7102 | CORD FOR POWER SUPPLY (3-Wire; Green; Black; and White) - Use on All Power Supplies | EACH | $11.66 | |
| 119 | 7272 | OUTDOOR TIMER (8hr; Programmable; GFCI) - Use to regulate cleaner's run time when no Auto shut-off | EACH | $46.58 | |
Information
Categories
Shopping Cart
Specials